Chimney Repair in Charleston, SC | Charleston Chimney Cleaning

Chimney Repair in Charleston - Camera Evidence Before Any Quote

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Masonry repairMasonry repair
Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Charleston Homeowners

Repair matters most when the chimney has stopped doing its two jobs: carrying smoke out and keeping water out. In Charleston’s humid climate, a cracked crown or failed flashing lets rain into masonry that then holds moisture for months, and the damage spreads quietly between burning seasons. Our technicians have up to experience diagnosing exactly where that moisture is getting in and what it has already touched. We work with six recognized trade brands – DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield – because professional-grade materials outlast hardware-store substitutes. We inspect it, we fix it, and you get one company accountable for the result. Same-day service is often possible when you call early. Reach us at (866) 864-1983.

Call (866) 864-1983

Chimney Cap Installation

Chimney Cap Installation means fitting a protective cover over the flue opening so rain, animals, and debris stay out while smoke and gases still escape freely. You need one when the flue is open to the sky, when birds or squirrels have found their way in, or when a light downdraft pushes smoke back into the room. We supply and install Gelco caps, sized to the flue rather than guessed at, so the fit is snug and the fastening holds through storm season. A typical cap installation in Charleston runs about $150 to $450 depending on flue size and cap type, and the written estimate sets the final price.

Why a Properly Sized Cap Matters

An undersized cap chokes draft and sends smoke into the living room; an oversized one rattles loose in wind. We measure the flue and match the cap to it. That single step prevents most of the callbacks we hear about from homeowners who bought a universal cap and fought with it.

Stainless and Powder-Coated Options

Stainless steel holds up best in humid Lowcountry air, and powder-coated caps suit homeowners who want the cap to blend with the roofline. We’ll walk you through both and explain which fits your chimney’s construction. Neither choice changes how the flue vents.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is swapping a damaged or missing cap for a new one before the flue sits unprotected through another rainy season. Rust-through, bent mesh, loose legs, and caps that have blown off in a storm are the usual reasons. We remove the old cap, check the flue tile and crown while we have access, and fit a new Gelco or Olympia Chimney cap to the measured opening. Typical replacement in Charleston runs about $175 to $500, and the written estimate from your free inspection sets the final price.

When Repair Beats Replacement

A cap with one loose screw or a small tear in the mesh usually just needs re-securing or a mesh patch. We tell you plainly when that’s the case instead of pushing a new cap. If the frame has rusted through, replacement is the honest answer.

What the Inspection Turns Up

Pulling a failing cap often reveals water damage on the crown or spalling in the top flue tile. We note it in the photo report so you see what we see. Nothing gets recommended without evidence you can look at yourself.

Chimney Liner Installation

Chimney Liner Installation creates a continuous, correctly sized flue inside the chimney so smoke and gases travel out without leaking through cracked or unlined masonry. You need a liner when the original clay tiles are cracked, when the chimney was built without one, or when a new appliance needs a flue matched to its exhaust. We install DuraFlex flexible stainless liners for most relines and use HeatShield resurfacing when the existing flue can be restored rather than replaced. A typical liner installation in Charleston runs about $1,800 to $5,500 depending on height, liner size, and whether insulation is added. The written estimate sets the final price.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 864-1983

Clay Tile Cracks and What They Mean

A cracked flue tile lets heat and gases reach framing close to the chimney, and that’s a fire risk no sweep can fix. We document every crack on camera before recommending a reline. If the tiles are sound, we’ll tell you so.

DuraFlex and HeatShield Compared

DuraFlex is a flexible stainless liner for chimneys that need a full new flue; HeatShield resurfacing rebuilds the interior of a flue that’s still structurally usable. We choose based on what the camera shows, not on what’s easiest to sell. Both are professional systems installed to the manufacturer’s spec.

Chimney Flashing Repair

Chimney Flashing Repair seals the joint where the chimney meets the roof, which is the single most common place water gets into a Charleston home. You need it when you see staining on the ceiling near the chimney, rust on the flashing metal, or gaps where the roofing meets the masonry. We replace step flashing, counter-flashing, and the sealant layer as needed, and we check the surrounding shingles while we’re up there. Typical flashing repair in Charleston runs about $350 to $900 depending on roof pitch and how much of the old flashing has to come off. The written estimate sets the final price.

Why Flashing Fails Before the Roof Does

Flashing moves with the roof through every heat cycle, and the sealant cracks long before shingles wear out. That’s why a roof can look fine while water still runs down the chimney. Inspecting the flashing is part of every repair visit.

Telling Roof Leaks From Chimney Leaks

Water on the ceiling near the chimney doesn’t always come from the chimney. We trace where it’s actually entering so the repair targets the right spot. Guessing here gets expensive fast.

Chimney Crown Repair

Chimney Crown Repair fixes the concrete cap on top of the chimney that sheds water away from the flue and masonry below. You need it when the crown is cracked, crumbling, or pulling away from the flue tile, because a failing crown lets water soak straight into the chimney body. We remove the loose material, rebuild the crown with a proper slope and overhang, and seal it against the flue. Typical crown repair in Charleston runs about $400 to $1,200 depending on crown size and how much of it has broken down. The written estimate sets the final price.

Hairline Cracks and Real Breaks

Small surface cracks in a crown are normal and often sealable. Wide breaks, spalling edges, and crowns that have separated from the flue are a different problem. We show you the difference on camera before recommending either.

Rebuilding With Proper Slope

A crown that sheds water correctly slopes away from the flue on all sides. Many original crowns were poured nearly flat, which is why they fail early. We rebuild with the slope the crown should have had.

Chimney Repair Companies

Chimney Repair Companies vary widely in what they can actually do once an inspection finds a problem. Some sweep and stop there; some diagnose and then hand you a list of parts to source yourself. We handle the full cycle – sweep, inspection, and repair – with DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield materials we know well. Typical repair work in Charleston runs about $350 to $5,500 depending on scope, from a small flashing fix to a full reline. The written estimate sets the final price, and we never bill for anything you didn’t approve.

Want to talk it through?Free estimate, price agreed before work starts
Call (866) 864-1983

What to Ask Before You Hire

Ask whether they do repairs or only sweeping, whether they use camera inspection, and whether the estimate is written and itemized. A company that can’t answer all three is probably not set up for repair work. We’re happy to be asked all of them.

Single-Source Accountability

When one company inspects and repairs, there’s no gap where the inspector blames the mason and the mason blames the inspection. We treat the chimney as a system and stand behind the whole result. If something’s not right, you call one number.

Chimney Masonry Repair

Chimney Masonry Repair restores the brick and mortar above the roofline, where weathering and water do the most damage. You need it when mortar joints are recessed or crumbling, when bricks are spalling or flaking, or when the chimney leans or has visible movement. We repoint joints, replace failed brick, and add a water-repellent coating after repairs cure – and we use HeatShield inside to resurface flues that can be restored rather than rebuilt. Typical masonry repair in Charleston runs about $600 to $3,000 depending on the height of the repair and the extent of the damage. The written estimate sets the final price.

Spalling Brick and What Causes It

Spalling happens when moisture gets into brick and freezes or expands, popping the face off. New brick with the wrong porosity makes it worse. We match brick to the existing chimney so the repair doesn’t just push the problem down the wall.

Repointing vs. Rebuilding

Repointing – replacing failed mortar joints – solves most masonry problems and is far cheaper than rebuilding. When the brick itself has failed through, rebuilding the affected section is the honest call. We’ll tell you which one you actually need, with photos to back it up.

Brands We Service

HeatShield gives us a way to resurface a damaged flue from the inside without tearing out the chimney, and we’re trained in its application. We know where the system holds up and where a full reline is the better answer. DuraFlex flexible liners are our go-to when a new flue is needed, and we spec the correct diameter so the appliance vents as it should. Gelco caps are what we install on most flues, sized to the opening and fastened properly rather than dropped on. Olympia Chimney components come into play on specialty venting runs, and Famco venting lets us handle the less common setups that show up on older Charleston chimneys.

We don’t sell parts out of a retail counter, and we don’t tell you to source anything yourself. Whether you have HeatShield, DuraFlex, Gelco, Olympia Chimney, Famco, or any other make, we can help. Each brand is a material choice – and the right material installed properly is what makes a repair last. See our Charleston Chimney Cleaning overview for how sweep, inspection, and repair fit together.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need a price for your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 864-1983

Signs You Need a Pro Right Now

  • Water stains on the ceiling near the chimney. Dark rings or brown streaks on drywall close to the chimney point to flashing or crown failure. Catching it early means a small repair rather than a rebuild of the wall and framing below.
  • Crumbling mortar or flaking brick on the chimney exterior. Mortar that’s receded from the joints or brick faces that are peeling off mean the masonry is absorbing water. Left alone, the damage deepens with each season and the repair grows.
  • Strong creosote smell or smoke backdraft. A heavy smell on warm days or smoke rolling into the room when you light the fire can mean a blocked flue or failing liner. Get it inspected before the next burn – this is a fire and carbon monoxide concern.
  • Rust or corrosion on the damper or firebox metal. Rust inside the firebox usually means water is entering from above. It’s a sign the crown or cap has failed, not just a cosmetic problem.
  • A cap that’s bent, missing, or loose. A storm can dislodge a cap and leave the flue open to rain and wildlife. Call us; we can often get out the same day or book you into the next available slot.

Our Process, Step by Step

  1. 1
    Call and book a visit. Call (866) 864-1983. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll ask what you’re seeing or smelling so we send the right technician.
  2. 2
    Inspection with camera. We run a video camera down the flue, check the firebox and damper, and look at the exterior – crown, flashing, cap, and masonry. You see the same footage we do, and we leave you with a photo report.
  3. 3
    Explanation and written estimate. We tell you what we found, what it means, and what it will cost – line by line. Nothing is recommended without camera evidence you can review yourself, and we say plainly when work can safely wait.
  4. 4
    Repair, done right. Once you approve the estimate, we do the work with the brand materials matched to your chimney – DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, or Copperfield as the job calls for. We protect the surrounding surfaces while we work.
  5. 5
    Final check and cleanup. We run the camera again after the repair to confirm the fix, test the draft where the work touches the flue, and leave the space cleaner than we found it. You get the update report to file with your home records.

How Much Does Chimney Repair Cost in Charleston?

Chimney repair in Charleston typically runs from about $150 for a simple cap or flashing fix up to roughly $5,500 for a full liner installation. A typical chimney cap installation runs $150-$450 depending on flue size. Chimney crown repair usually runs $400-$1,200, and chimney flashing repair runs $350-$900 depending on roof pitch. Masonry repair for spalling brick and crumbling mortar runs $600-$3,000, and a liner installation or reline runs $1,800-$5,500. All prices are estimates; the written estimate sets the final price.

What drives cost in this market: the height of the chimney, how much of the masonry has failed, whether the repair can happen from the roof or needs access work, and whether the flue needs resurfacing or a full reline. Roof pitch matters more than most homeowners expect because steep roofs take longer to work on safely. Single-story ranches and older two-story homes tell two very different stories.

To avoid overpaying, ask for a written, itemized estimate and a photo report before you agree to anything. A company that won’t show you camera footage of the problem is asking you to trust a story. We never recommend liner or masonry work without evidence you can look at yourself, and we’ll tell you when work can safely wait a season. Our estimate is free, and it includes the inspection and photo documentation that justify every line item. Call (866) 864-1983 for an exact quote – estimates are free.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 864-1983

Our Service Area Near Charleston

We serve homeowners in Charleston and the surrounding communities, including Mount Pleasant, James Island, Hanahan, Goose Creek, Isle of Palms, Hollywood, Ladson, Ravenel, Sangaree, Summerville, and Moncks Corner. Response times depend on where you are and what the job requires, but we book visits promptly and we tell you honestly when a slot is available. See our chimney repair page for the Mount Pleasant area, and our chimney repair page for James Island, or read about chimney repair closer to the city itself.

Serving Charleston, SC – Our Local Coverage Area

We serve Charleston and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Charleston

Schedule Your Chimney Repair Service in Charleston Today

A chimney problem doesn’t get cheaper with time. Book a visit, get a camera inspection and photo report, and approve only what needs doing – capped by a written estimate. Call (866) 864-1983. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free and there’s no obligation. From sweep to repair, one call covers it.

Written by the team at Charleston Chimney Cleaning.

Why Charleston Chooses Charleston Chimney Cleaning

We set the standard for chimney repair in Charleston.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Charleston

Getting your chimney repair project started is simple.

1

Call or Request a Free Estimate

Tell us about your chimney repair project and we set up a free visit. No obligation and no hidden fees.

2

Licensed Estimator Visits

A licensed, insured estimator inspects and measures on site, then gives you a clear written price.

3

Scheduled and Done Right

Your crew does the work on the date in your quote, backed by our workmanship warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Charleston Customers Say

Trusted by homeowners across Charleston and surrounding areas.

★★★★★

"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."

Adam Thompson
★★★★★

"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."

Rachel Barrett
★★★★★

"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."

Holly Brooks

Ready for Chimney Repair in Charleston?

Call now for a free estimate, or request one below. Licensed, insured, and ready to schedule your free estimate in Charleston.

(866) 864-1983

Request a Free Estimate in Charleston

Tell us about your chimney repair needs. We'll get back to you to set up your free estimate.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Local Service Coverage
Call Now - We Answer 24/7